Some parts cannot tolerate the heat of laser or plasma cutting. Waterjet is often considered for exactly these cases, yet it brings its own limits in speed, taper and tolerance. The sections below cover how the process works and where it fits.
What Is Waterjet Cutting?
Waterjet cutting is a cold cutting process that erodes material with a high-pressure water stream, typically 40,000 to 60,000 psi, forced through a small orifice. For harder materials such as metals, stone and ceramics, abrasive garnet is mixed into the stream. Because cutting relies on erosion rather than heat, no heat-affected zone forms.
Types of Waterjet Cutting
Waterjet systems are classified by whether abrasive is added to the stream. This determines which materials can be cut and how thick they can be.
Pure Waterjet Cutting
Pure waterjet uses only high-pressure water through a sapphire or diamond orifice, typically 0.1 to 0.4 mm in diameter. The narrow stream produces a kerf of about 0.1 to 0.3 mm with no abrasive residue. It suits soft materials such as rubber, foam, gaskets, thin plastics and composites.
Abrasive Waterjet Cutting
Abrasive waterjet adds garnet, commonly 80 mesh, to the stream through a mixing tube. The abrasive gives the jet enough cutting force for steel, titanium, stone, glass and ceramics. Kerf width is typically 0.8 to 1.2 mm, and cuttable thickness can exceed 100 mm, depending on the material and machine.
Benefits of Waterjet Cutting
The main benefits of waterjet machining come from its cold, force-light cutting action, which affects both the cut part and how a job is planned.
- No heat-affected zone: Erosion cutting leaves material hardness, grain structure and flatness unchanged, which matters for hardened alloys and heat-treated parts.
- Low cutting force: The jet exerts little force on the workpiece, so thin or brittle parts can be cut without cracking or clamping distortion.
- Wide material range: One machine cuts steel, aluminum, titanium, stone, glass, ceramics, rubber and composites.
- Efficient material use: The narrow kerf allows tight nesting, which reduces scrap on expensive materials such as titanium and Inconel.
- No toxic fumes or dust: Garnet and water are the only consumables, and cutting produces no combustion gases. Waste garnet can usually be disposed of as non-hazardous material.
Waterjet Cutting vs Other Cutting Methods
The right cutting method depends on material, thickness, tolerance and how much heat the part can tolerate. The table compares waterjet with three common alternatives.
| Factor | Waterjet | Laser | Plasma | Wire EDM |
|---|---|---|---|---|
| Cutting principle | Abrasive erosion | Melting and vaporizing | Ionized gas arc | Electrical discharge |
| Suitable materials | Nearly all materials | Metals, some plastics | Conductive metals only | Conductive metals only |
| Typical max thickness | 100 mm and above | Up to about 25 mm (steel) | Up to about 50 mm | Up to about 300 mm |
| Typical tolerance | ±0.1 mm | ±0.05 to 0.1 mm | ±0.5 to 1 mm | ±0.005 to 0.01 mm |
| Heat-affected zone | None | Narrow | Wide | Thin recast layer |
When to Choose Each Method
- Waterjet: Best for thick plate, non-metallic materials and parts where heat would change the material’s properties.
- Laser: Suited to thin sheet metal with fine features and high volumes, where speed and edge quality matter most.
- Plasma: A cost-effective option for thick structural steel where tolerance and edge finish are less critical.
- Wire EDM: Used for hardened conductive materials that need very tight tolerances and sharp internal corners.
For a full breakdown of how these four methods compare on cost, speed and application fit, see our guide to EDM vs laser vs waterjet vs plasma cutting.
Conclusion
Waterjet project suits heat-sensitive materials, thick plate and mixed-material jobs, but a cut profile is rarely the finished part. Features such as pockets, threads and tight-tolerance bores still need machining. Our CNC machining service covers 3-axis, 4-axis and 5-axis work at ±0.025 mm general tolerance. Send your drawings for a quote.
Need Custom CNC Machined Parts?