Feed rate, spindle speed and tool geometry work together. A well-matched rake angle allows higher material removal rates without raising tool load. The sections below cover rake angle types and how to choose one.
What Is Rake Angle?
On a CNC mill or lathe, rake angle (γ) is the angle between the tool’s rake face (the surface the chip slides across) and a line perpendicular to the machined surface. It is defined in degrees and set mainly by tool or insert geometry, not by the machine program. Selecting a tool therefore means selecting a rake angle.
How to Measure Rake Angle?
Rake angle is measured on the cutting edge’s cross-section, in a plane perpendicular to the edge, against a reference line perpendicular to the cutting direction. Optical comparators, toolmaker’s microscopes and vision systems all rely on this setup.
- Optical comparator: The tool is magnified and projected onto a screen, where the rake face profile is overlaid with an angle scale or template. Suitable for end mills, drills and ground tool bits.
- Tool presetter or tool measuring machine: An optical system captures the edge profile and calculates the angle automatically. Repeatable, and used for checking tools before they go into the spindle.
- CMM or 3D optical scanner: Scans the rake face and a reference plane, then calculates the angle from the measured geometry. Suited to complex flute shapes and variable-rake tools.
- Bevel protractor or angle gauge: A manual check on larger single-point tools. Fast, but accuracy is lower than the optical methods and depends on the operator.
Types of Rake Angle
Tool geometry uses a sign convention to classify rake angle. Positive rake leans away from the workpiece, negative rake leans toward it, and zero rake has no tilt.
Positive rake angle
A positive rake angle means the rake face tilts away from the workpiece. The edge is sharper and shears material instead of pushing it, which reduces cutting force and heat. Typical values on CNC tools range from about +5° to +20°, and higher on some tools for aluminum.
Advantages of Positive rake angle
- Lower cutting force: Less power is required, which reduces deflection on thin-wall parts and in low-rigidity setups.
- Less heat at the cutting zone: Chips deform less and leave the cut more easily.
- Better surface finish: The sharp edge shears cleanly and reduces burrs and smearing.
- Reduced built-up edge: Works well on soft, ductile materials such as aluminum, copper and thermoplastics.
Disadvantages of Positive rake angle
- Weaker cutting edge: Less material supports the edge, so chipping risk rises with higher angles.
- Poor suitability for hard materials: Hardened steel and abrasive materials wear the edge quickly.
- Limited performance in interrupted cuts: Impact loads can break the edge.
- Lower heat dissipation through the tool: Less tool material sits behind the edge to conduct heat away.
Negative Rake Angle
A negative rake angle means the rake face tilts toward the workpiece. The edge is blunter but has a thick wedge of tool material behind it, so the cutting load is carried by a stronger section. Typical values range from about -5° to -15°, and it is the standard geometry for most indexable carbide inserts.
Advantages of Negative Rake Angle
- Strongest cutting edge: The thick wedge resists chipping and fracture under heavy loads and interrupted cuts.
- Better heat dissipation: More tool material behind the edge carries heat away from the cutting zone.
- Suited to hard materials: Hardened steel, cast iron and high-strength alloys can be machined with good tool life.
- Allows higher feeds and depths of cut: The robust edge supports aggressive roughing.
- Double-sided inserts: Negative-rake inserts can often be used on both faces, giving more cutting edges per insert.
Disadvantages of Negative Rake Angle
- Highest cutting force: The blunter edge pushes material and raises power demand and spindle load.
- More heat in the chip: Higher friction and chip deformation increase cutting temperature.
- Needs a rigid setup: High force can cause deflection and chatter on thin walls or long-overhang tools.
- Poor fit for soft or gummy materials: Aluminum and plastics tend to smear or form built-up edge.
Zero Rake Angle
A zero rake angle means the rake face sits perpendicular to the cutting direction, with no tilt toward or away from the workpiece. The edge is stronger than a positive rake edge, and cutting force is moderate. It is common on form tools, cut-off tools, and tools for brass and some plastics.
Advantages of Zero Rake Angle
- Stronger edge than positive rake: More tool material sits behind the edge, improving resistance to chipping.
- Stable and predictable cutting: Chip flow and force are easy to control, which suits form tools and grooving.
- Simple to grind and resharpen: The flat rake face keeps tool geometry consistent after regrinding.
- Suited to free-machining materials: Brass, bronze and some plastics cut well without chip pull-in.
Disadvantages of Zero Rake Angle
- Higher cutting force than positive rake: The edge pushes more material than it shears, raising spindle load.
- More heat in the cut: Thicker chips and more friction increase temperature at the tool tip.
- Weaker surface finish on soft metals: Aluminum and copper can smear or build up on the edge.
- Less impact resistance than negative rake: Interrupted cuts and hard materials still carry a risk of edge damage.
How to Choose the Right Rake Angle
Rake angle selection follows a simple logic: soft materials favor sharper edges, and hard materials or heavy cuts favor stronger ones. Several factors refine that rule.
Workpiece Material
Material hardness and ductility set the starting point. Aluminum and copper cut best with +12° to +20° positive rake. Carbon steel and stainless steel typically use 0° to +10°. Hardened steel and cast iron call for negative rake, around -5° to -10°.
Type of Cut
Roughing, finishing and interrupted cuts load the edge differently. Finishing passes benefit from positive rake for low force and a cleaner surface. Heavy roughing and interrupted cuts, such as milling a part with slots or cross holes, need the edge strength of zero or negative rake.
Machine and Setup Rigidity
Positive rake lowers cutting force, which helps on thin-walled parts, long-overhang tools and lighter machines. Negative rake raises force and requires a rigid spindle, secure workholding and short tool stick-out. Without that rigidity, deflection and chatter reduce accuracy.
Tool Material
High-speed steel tolerates larger positive angles because it is tougher. Carbide is harder but more brittle, so it usually runs smaller positive angles or negative rake, especially on indexable inserts. Coatings and edge preparation, such as a honed edge, add strength to the cutting edge.
Conclusion
Rake angle is one parameter in a larger machining plan that also includes speeds, feeds and workholding. Zhongde’s CNC Machining Service combines these decisions across 3-axis, 4-axis and 5-axis machining, and also produces precision parts such as bushings to ±0.025 mm. Share your requirements to receive a quote.
Need Help with Your CNC Machining Project?