Yield Strength Test

How Yield Strength Affects Material and Part Design

Table of Content

Yield strength marks the end of elastic behavior and the start of permanent deformation. It is one of the first values engineers check on a material datasheet. This article explains how it is determined from a stress-strain curve and what it means for part design.

What Is Yield Strength?

A shaft that stays bent after a load is removed, or a plastic clip that does not return to its original position, has been stressed beyond its yield strength. The part has not fractured, but it no longer meets its dimensional requirements. Yield strength is the value that predicts this condition.

How Yield Strength Is Measured?

Yield strength is measured with a uniaxial tensile test. A standardized specimen is pulled at a controlled rate until it deforms permanently, while force and elongation are recorded. The yield strength is then read from the resulting stress-strain curve.

Stress-Strain Curve
Stress-Strain Curve

Test Procedure

  1. Prepare the specimen. Machine or mold a specimen to the dimensions required by the test standard. Dumbbell shapes are used for plastics, and round or flat bars for metals.
  2. Measure the original cross-section. Record width and thickness, or diameter, at the gauge section. This value (A₀) is used to convert force into stress.
  3. Mount the specimen. Clamp both ends in the grips of a universal testing machine and attach an extensometer to the gauge length to record strain accurately.
  4. Apply the load. Pull the specimen at a constant crosshead speed or strain rate, as specified by the standard.
  5. Record the curve. Plot stress (force ÷ A₀) against strain until the yield point is passed. Testing usually continues to fracture to obtain tensile strength and elongation as well.

Reading the Stress-Strain Curve

The curve has four regions that matter for yield strength.

RegionWhat it shows
Elastic regionStraight line where stress is proportional to strain. Its slope is the modulus of elasticity, and the specimen recovers fully when unloaded.
Yield pointWhere the curve leaves the straight line and permanent deformation begins.
Plastic regionStrain increases faster than stress, and the deformation is not recovered after unloading.
Ultimate tensile strength and fractureThe highest stress on the curve, followed by necking and break.

The yield point is located in different ways depending on the material:

  • Distinct yield point. Mild steel shows a sudden drop in stress at yielding. The stress at this point is reported as the upper yield strength, and the lower plateau as the lower yield strength.
    Yield Strength Mild Steel Curve
    Yield Strength Mild Steel Curve
  • 0.2% offset method. Aluminum alloys and stainless steels have no clear yield point. A line is drawn parallel to the elastic slope, offset by 0.2% strain, and the stress where it crosses the curve is the yield strength (also called 0.2% proof strength).
    Yield Strength 0.2 Offset Curve
    Yield Strength 0.2 Offset Curve
  • First stress maximum. Many plastics reach a local peak in stress before the curve flattens or drops. The stress at this peak is reported as the yield strength.
    Yield Strength Thermoplastic Curve
    Yield Strength Thermoplastic Curve

Some brittle materials, including heavily glass-filled plastics, fracture before reaching a yield point. For these, tensile strength at break is reported instead.

Why Yield Strength Matters?

The yield strength of a material directly influences structural dimensions, load capacity and weight. It is an important parameter in mechanical design and optimization.

Sets the Design Limit

Engineers use yield strength to establish allowable working stress, applying a safety factor to prevent permanent deformation. For example, a 6061-T6 aluminum alloy with a 275 MPa yield strength and a 1.5 safety factor has an allowable stress of approximately 183 MPa.

Prevents Permanent Deformation

Keeping working stress below yield helps prevent bent brackets, loose fits, misaligned shafts and leaking seals. This protects dimensional accuracy and functional performance under service loads.

Supports Material Selection

Yield strength provides a common basis for comparing material resistance to permanent deformation. Mild steel (250 MPa), 6061-T6 aluminum (275 MPa) and ABS (40 MPa) illustrate how load capacity differs across material types.

Guides Wall Thickness and Weight

Higher yield strength can allow thinner load-bearing sections under the same loading conditions, reducing material use and part weight. This is an important design trade-off when selecting between metals and plastics.

Yield Strength vs Tensile Strength

Yield strength and tensile strength are both read from the same stress-strain curve, but they mark different events. Yield strength is the stress where permanent deformation begins. Tensile strength, also called ultimate tensile strength (UTS), is the highest stress the material reaches before it fractures.

Yield Strength VS Tensile Strength
Yield Strength VS Tensile Strength
ComparisonYield StrengthTensile Strength
DefinitionStress at the onset of permanent deformationMaximum engineering stress during a tensile test
Mechanical behaviorMarks the transition to plastic deformationMarks the peak load-bearing stress
Position on curveAt the yield point or proof stressAt the highest point of the curve
Design purposeSets allowable working stressEvaluates maximum tensile load capacity
Engineering concernPreventing permanent deformationAssessing tensile performance and failure resistance
Common notationσy or SyUTS or σUTS

Which Value Matters More in Design?

The choice depends on how the component is expected to perform under load.

  • Yield strength for dimensional stability: Use yield strength when a part must retain its original shape under working loads. For example, a metal bracket should remain straight under its intended load rather than bend permanently.
  • Tensile strength for maximum load capacity: Use tensile strength when assessing how much tensile stress a material can withstand before reaching its maximum engineering stress. This is important for components such as tension rods and cables.

For most load-bearing designs, engineers check both values alongside the safety factor, fatigue resistance and operating conditions. Neither value alone is sufficient to determine whether a material is suitable for an application.

Factors That Influence Yield Strength

Yield strength depends on material composition, internal structure and processing conditions. Several factors determine how much stress a material can withstand before permanent deformation begins.

Material Composition

Alloying elements and polymer composition affect the strength of a material. For example, carbon content influences the strength of steel, while polymer type, molecular structure and additives affect the yield behavior of plastics.

Grain Size and Molecular Structure

In metals, finer grain sizes generally increase yield strength by restricting dislocation movement. In plastics, molecular weight, chain arrangement and crystallinity influence resistance to deformation.

Heat Treatment

Heat treatment changes the internal microstructure of metals and can significantly alter yield strength. Processes such as quenching and tempering are commonly used to adjust the strength and ductility of steel alloys.

Processing Conditions

Manufacturing conditions can affect the final mechanical properties of a material. For plastics, cooling rate, molding temperature and processing conditions influence crystallinity, molecular orientation and residual stress, which can change measured yield strength.

Temperature and Loading Conditions

Yield strength generally decreases as temperature rises in many metals and plastics, although the extent varies by material. Strain rate also affects measured yield strength, particularly in polymers, which exhibit time-dependent mechanical behavior.

Design Considerations for Yield Strength

Using yield strength in component design requires more than checking the material’s published value. Engineers must account for loading conditions, part geometry, safety factors and the material’s behavior throughout its service life.

Calculate the Maximum Working Stress

Determine the nominal stress under the expected load using the original cross-sectional area:

σ = F / A₀

Where:

  • σ = Applied stress (MPa)
  • F = Applied force (N)
  • A₀ = Original cross-sectional area (mm²)

For example, a component with a 200 mm² cross-section under a 20 kN tensile load experiences a nominal stress of 100 MPa.

Apply an Appropriate Safety Factor

Set the allowable stress by dividing the material’s yield strength by the selected safety factor:

σ_allow = σ_y / n

  • σ_allow = Allowable stress (MPa)
  • σ_y = Yield strength (MPa)
  • n = Safety factor

For a 6061-T6 aluminum component with a yield strength of 275 MPa and a safety factor of 1.5, the allowable stress is approximately 183 MPa.

Compare the calculated working stress with this limit. In this example, 100 MPa is below 183 MPa, so the component satisfies the nominal tensile stress criterion.

Size the Load-Bearing Section

Higher yield strength can allow a smaller load-bearing cross-section. Under a simple axial tensile load, the required area can be estimated using:

A ≥ F × n / Sy

Where:

  • A = Required cross-sectional area (mm²)
  • F = Applied tensile force (N)
  • n = Safety factor
  • Sy = Yield strength (MPa or N/mm²)

Check Stiffness and Structural Stability

A component can remain below its yield strength but still deform excessively or become unstable under load. For a uniform axial member, elastic elongation can be estimated using:

δ = (F × L) / (A × E)

Where:

  • δ = Elastic elongation (mm)
  • F = Applied force (N)
  • L = Original length (mm)
  • A = Cross-sectional area (mm²)
  • E = Young’s modulus (MPa or N/mm²)

For slender components under compression, buckling may occur before the material reaches its yield strength. Engineers should therefore check both deformation and structural stability, particularly when designing thin-walled or long load-bearing parts.

Conclusion

Reliable component design requires more than selecting a material with sufficient yield strength. Engineers must also account for working stress, stress concentrations, stiffness and operating conditions. With Zhongde CNC Machining Service, customers can source custom metal and engineering plastic components based on their drawings, material specifications and dimensional requirements.